Product Description
American Dish Service ( R-L ) 44" High Temp Conveyor, 240V /3 PH, w/ Built on Booster, 4" Vents, Voltage & Phase Required
***PLEASE NOTE THESE DISH MACHINES CAN HAVE A 13 WEEK LEAD TIME***
Standard Features
All these features are Standard on the ADC-44. While other manufacturers may offer these same features as Add-Ons, at American Dish our machines are complete and ready to run.
244 racks per hour
Operates only when racks are inserted
Unrivaled cleaning ability
Dual rinsing system
User friendly conveyor
Low Water Consumption - Uses as little as .49 gallons per load
Auto Fill
No Operator Controls
Energy Saving Stage Washer
No Circuit Boards
Quiet Operation
Rack Saving Conveyor Drive
360 Sq. in. of Washing Action
Auto Cut-Off
High Capacity Heaters
Self-Purging
Wide Opening Access Doors with Safety Interlock
11 Gallon Wash Tank
3 HP Wash Pump
Skirted Motor Compartment
Heavy Stainless Steel Construction
Water Curtain Rinseability
Activates prior to final rinse
Initiates the rinsing process and acts as a shield
Captive end caps
Flips open, snaps shut
Quick fast clearing of spray arms
Shortens the cleaning process & eliminates down time
Drain Pump Filter
2 stage pump strainer
Eliminates wash pump obstructions and clogged jets
Funtions as drains stopper
Dual-Fail Safe Heater Control
Precise water control mechanism
Only allows heaters to operate when tank is full
Unaffected by heavy soil, water action, strong chemicals and lime build up
Fail-Safe Conveyor System
Slip clutch design - stops rack movement
Once removed, operation easily resumes
Eliminates damaged racks
Specifications
ADC-44 Spec Sheet (PDF)
Capacities
NSF Rated Capacity: 244 rack/hour
Conveyor Speed: 6.8 ft/min
Motor Horsepower
Wash: 3 horsepower
Rinse: 1/3 horsepower
Conveyor: 1/3 horsepower
Water Consumption
Gal per rack: .49 gpr or 1.8 liters
Temperatures
ADC-44 Hot Temp Model Wash: 160 F
ADC-44 Chemical Model Wash: 120 F
ADC-44 Hot Temp Rinse: 180 F
ADC-44 Chemical Rinse: 120 F
Heating
Wash: 12 kW
Rinse: 2.25 kW
Sanitizer
ADC-66 Hot Temp Model: 180 Water
ADC-66 Chemical Model: 50ppm Chlorine
Utilities & Other Notes
Power Supply
208/240V, 3 PH, 60 AMP, 60 HZ
3 Phase installation requires 3 gauge wires with a 10 gauge neutral wire, a suitable ground, and a clean circuit.
1 PH, 50/60 AMP, 60 HZ
1 Phase installation requires one (1) 50 Amp service using 8 gauge wires with a 10 gauge neutral wire, and one (1) 60 Amp service using 6 gauge wires and a suitable ground, both on clean circuits.
Other Notes
Both clean and soiled tables are to be bolted to the dishmachine with the 1/4-20?1/2? bolts and nuts provided.
Leaks cause potential problems in electrical and mechanical areas under the machine.
Quick drains (table scuppers) are not compatible with stage type conveyor dishmachines.
Scrap sinks shall be no closer than 20? minimum from the dishmachine end of table.
The clean exit table should be at least 72? straight for efficient conveyor operation.
Electrical and plumbing connects should be made by a qualified service person who will comply with all appropriate state and local health, electrical, plumbing, and safety codes.
*Manufacturer reserves the right to modify these specifications in compliance with regulatory agencies and manufacturing expediency.
|
